Showing 151–160 of 239 results

SERIES PMS , DWYER ,Particulate Sensor

The PMS Particulate Sensor employs a field-proven combination of passive-induction and protected-probe technologies. As particles flow near and around the probe, minute currents are dynamically induced into the probe by flowing particulate. A DSP processes the signal into an absolute output that is reasonably linear to mass. Protective layers over the probe work in combination with induction-sensing to ensure reliable operation with all types of particulate including moist powders and highly conductive dusts. Maintenance is minimal and there is no need for an air purge. For durability, the sensors are passive and free of electronics. The PMS Particulate Sensor is designed to be used with the DPM Particle Monitor in order to be intrinsically safe.

SERIES DPM, DWYER ,Particulate Monitor

The DPM Particulate Monitor and PMS Particulate Sensor combine to provide a basic baghouse and cartridge filter leak detector designed for general maintenance planning and process protection. It is easy to use and reliable. Leakage is gaged in real-time, on-the-spot, without prior baseline data and without signal tuning. Simply apply power and the general condition of the filter is quickly determined. An alarm point is set by simply moving an indicator up and down the gage with the convenient, lockable key pad. For more precise alarm setup the large display provides both a logarithmic analog bar graph and an absolute digital readout. The log scale enables the user to observe both the baseline bleed through and the high peaks that are caused by filter cleaning cycles and developing leaks. Observation of both baseline and peaks is essential to setting proper alarms. The digital readout in absolute units ensures correct interpretation of the readings and provides accurate historical comparisons.

SERIES VBT-1 , DWYER ,Vibration Transmitter

The Model VBT-1 Vibration Transmitter continuously detects the vibration in a system and monitors for unusual operating conditions and potential failure. The vibration is converted into an analog signal at the current output. The VBT requires no setup, and there is no software required for configuration. The 2-wire loop power operation, combined with standard M12 micro cable connector and interchangeable mounting studs (1/4″-28 UNF/M8 (2) or the 1/4″-28 UNF), makes for a fast and reliable installation.

Series VBS , DWYER ,Vibration Switch

The Series VBS Vibration Switch is small, compact, and uses two easy set up dials that adjust the maximum RMS velocity set point and false trip time delay. The Series VBS is intended to continuously monitor the changes in a machine’s vibration level. The VBS takes real-time RMS vibration input and provides an analog output of velocity as well as a switching output when an alarm value is exceeded.

SERIES MN-1 , DWYER ,Mini-Node™ Communication Signal Converter

The Model MN-1 Mini-Node™ Communication Signal Converter is a low cost device that converts half duplex RS-485 serial communications signals into a signal that can be read by any computer with a USB port. The integral USB connector and RJ-45 connector reduces set up time by eliminating extra wiring. The Model MN-1 is powered via the USB connection which eliminates the need for an external power source. The compact size is great for field installation, control panels, and lab testing.

SERIES MTL20/30 , DWYER ,Miniature USB Data Logger

The Series MTL Miniature USB Data Logger measures and records accurate readings for temperature or temperature/humidity/dew point in a wide range of applications. Sampling intervals and high/low alarm settings are user selectable through the included easy to use Windows® based software. On models ordered with an integral display, the temperature and humidity readings alternate on the display. The series MTL can be software configured to begin measuring based on a time delayed-start or by push-button. The logger can store up to 43,344 readings and can be set to stop on memory full or for continuous recording. Stored data is downloaded by plugging the unit into a PC’s USB port (cable included). The loggers provide measurements for many environment conditions, which make them ideal for refrigeration systems, laboratories, and medical storage facilities.

SERIES CSE-KN, DWYER ,Carbon Steel Enclosure with Knockouts

THE SERIES CSE-KN CARBON STEEL ENCLOSURES are spot-welded, wall mounted enclosures designed to house electrical controls, instruments, and components in general purpose areas with knockouts to allow cords to pass easily into the unit. The door features butt hinges that allow 180° of rotation, a keylocking quarter turn latch, and a ground stud. Mounting holes on the back of the enclosure allow for versatile mounting. Each enclosure includes a sub-panel with a 2″ x 2″ (50.8 mm x 50.8 mm) mounting grid mounted on standoffs and lock with keys. This series is the perfect accessory for a variety of instrumentation in need of general protection and extra security.

SERIES CSE-N1 , DWYER , Carbon Steel Enclosures

THE SERIES CSE-N1 CARBON STEEL ENCLOSURES are spot-welded, wall mounted enclosures designed to house electrical controls, instruments, and components in general purpose areas. The door features butt hinges that allow 180° of rotation, a quarter turn latch than can be opened/closed with a screwdriver, and a ground stud. Mounting holes on the back of the enclosure allow for versatile mounting and standoffs provide easy installation of optional sub-panels. Each unit offers optional solid or perforated sub-panel and mounting straps for easy instrument mounting. This series is the perfect accessory for a variety of instrumentation in need of general protection and security.